Parts & Accessories

SRAM's Quick Releases hold your wheel tightly in place, are built for ease of use and made to last, too. You get a front and rear quick release.

Durasync freehub bodies feature triple freehub bearings for increased axle stability to handle even greater vertical and torsional loads. This CNC machined durasync freehub is a direct replacement for your Neo hub, and includes pawls, springs, pawl retaining ring, and red freehub spacer. Bearings are pre-installed. - 6-pawl system provides 36 points of contact and 10-degree engagement for quick acceleration - Chromed steel bearings - Wide bearing stance and axle design reduces flex and adds durability - Low drag main seal prevents contamination and reduces resistance - Mini Driver has a Shimano HG spline, but is 10mm shorter to accept 11-speed cassettes with 10t cogs from Hope and OneUp Components

Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).

Maxle Ultimate Lever Assembly - Fits Maxle Ultimate B1 - Includes lever section only - Suitable for suspension forks

Upgrade or refresh your Bontrager wheels. Genuine replacement parts Whether you're looking to upgrade to the newest and freshest drivetrain or simply hoping to refresh your trusty wheelset, Trek Genuine Replacement Parts have you covered. - Replacement parts for Bontrager hubs using the DT 240 platform - Compatible with all Bontrager wheels with DT 240 hub internals - For use with Shimano MICRO SPLINE cassettes - Includes 12mm thru-axle end cap

DT Swiss tubeless ready tape seals the rim for tubeless applications and also works well as rim tape for tube-type set ups. - Highly resistant adhesive tape works as a rim tape and airseal

Trainer ready. Keep the ride going by putting your Cannondale on a trainer with the 2-in-1 trainer axle. Where it thrives: The open road, on the trainer What it's built for: Versatility, convenience Highlights: - Fit your Cannondale road bike to any indoor trainer Removable end caps for outdoor riding - Compatible with Cannondale road bikes that utilize Speed Release dropouts

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

This conversion kit allows you to use SRAM's 11-speed mountain cassette on your Stan's NoTubes wheels. Each kit includes an XD freehub, spacer, drive side end cap, and three sealed bearings.

Upgrade or refresh your Bontrager wheels. Genuine replacement parts Whether you're looking to upgrade to the newest and freshest drivetrain or simply hoping to refresh your trusty wheelset, Trek Genuine Replacement Parts have you covered. - Replacement freehub body - Compatible with Bontrager Entry-level hubs

Upgrade or refresh your Bontrager wheels. Genuine replacement parts Whether you're looking to upgrade to the newest and freshest drivetrain or simply hoping to refresh your trusty wheelset, Trek - Replacement freehub body - Compatible with Kovee Elite 23, and Duster Elite wheels

Shimano, FH-M828/788/678/648, Freehub body, Y3TH98050

- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Drive Side Axle End Cap

125 piece assortment of precision machined axle spacers (0.5mm to 5mm thickness). - Outside Diameter of Spacers: 16mm - Inside Diameter of Spacers: 10mm Kit includes: - (10) - 0.5mm thick spacers - (30) - 1mm thick spacers - (30) - 2mm thick spacers - (25) - 3mm thick spacers - (15) - 4mm thick spacers - (15) - 5mm thick spacers

Ease of use, lightweight, and optimum performance in a single product. The DT Pro Head shape, combined with both a torx and a square tool interface, makes wheel building a lot easier. The spherical contact surface aligns the nipple perfectly with the spoke. All-brass nipples are recommended for e-bike use. Weight: starting at 26g for 64 nipples.

Upgrade or refresh your Bontrager wheels. Genuine replacement parts Whether you're looking to upgrade to the newest and freshest drivetrain or simply hoping to refresh your trusty wheelset, Trek Genuine Replacement Parts have you covered. - Replacement freehub body - Compatible with Bontrager Rapid Drive 108 hubs - Pawls and springs sold separately - Install 3 pawls/springs for 54 tooth engagement or 6 pawls springs for 108 tooth